Metallum3D Successfully Completes Validation Tests of New Microwave Heating Proc

3D printing news
2022
05/24
20:02
分享
评论
Over the last two years, Metallum3D has been developing a new type of microwave heating process that uses non-resonant, cross-polarized slotted waveguides and a granular susceptor material to evenly distribute microwave energy during processing. Until now, microwave energy has not been successfully used in additive manufacturing applications due to the uneven microwave energy distributions of the current multi-mode resonant technology. Recently, Metallum3D completed the construction of a second-generation microwave furnace that implements non-resonant, cross-polarized slotted waveguides as a microwave energy feeding system. A picture of the microwave furnace is shown below in Figure 1.

wp1.png

Figure 1


The performance of the non-resonant, cross-polarized slotted waveguides used in this microwave furnace has been simulated using the electromagnetic simulation software CST Microwave Studio. The simulations showed that the non-resonant, cross-polarized waveguides generate an electric field with uniform microwave energy distribution. Figure 2 shows a 3D CAD model of the non-resonant, cross-polarized waveguide pair and a simulation of the electric field being generated in free space. The uniform color distribution within the electric field cross-section is indicative of uniform microwave energy distribution.

wp2.png

Figure 2


A separate simulation was conducted to evaluate the performance of the non-resonant, cross-polarized slotted waveguides as mounted in the microwave cavity. Figure 3 shows the simulation of the electric field generated by the non-resonant, cross-polarized waveguides at the mid-section of the microwave cavity. The uniform color distribution within the electric field cross-section is indicative of uniform microwave energy distribution.

wp3.png

Figure 3


A recent validation study completed by Metallum3D utilized cast gypsum plates saturated in a cobalt chloride solution and thermal imaging to map the actual microwave energy distribution of the non-resonant, cross-polarized waveguides under operating conditions. After exposing the plates to a microwave field, the heating of the plates causes a color change in the cobalt chloride that forms a color map of the microwave energy distribution. The visual color map results were cross-validated with thermal imaging.
The Metallum3D microwave furnace uses two sets of waveguides, with each waveguide being directly fed by 1.5 kW magnetrons for a total of 6kW. Figure 4 shows the internal and external waveguide arrangement.

wp4.png

Figure 4


For validation testing, 6 casted plates were vertically loaded into the microwave with the aid of a PVC fixture as shown in Figure 5.

wp5.png

Figure 5


Microwave heating of the plates resulted in a uniform color change of all the plate surfaces from a pinkish-grey color to a bluish-gray color. There was no color banding in any of the plate surfaces indicating homogenous microwave heating throughout the entire microwave cavity volume. The visual results obtained were then cross-validated through thermal imaging, which also showed uniform microwave heating throughout the surfaces of all the plates. The actual microwave energy distribution of the non-resonant, cross-polarized slotted waveguides is in good agreement with the predicted microwave energy distribution previously obtained through electromagnetic simulation. A technical white paper detailing the validation testing and results is available for download at the following link:
Metallum3D Technical White Paper Download
The successful validation of this new type of microwave heating process by Metallum3D is creating new opportunities for processing additively manufactured parts. Our Microwave Furnace is configured for both microwave sintering and microwave digital casting. For microwave sintering, parts are embedded in a granular susceptor material within a microwave transparent and thermally insulating box for rapid microwave sintering, which is up to 90% faster than conventional sintering. A schematic representation of the Metallum3D microwave sintering process is shown in Figure 6.

wp6.png

Figure 6


Microwave Digital Casting is a process that combines additive manufacturing and microwave heating to create a new agile and cost-effective casting process that bypasses the need to pour molten metal into a mold. The first step in the microwave digital casting process is to 3D print a sacrificial ceramic shell mold. The second step is to fill the ceramic shell mold with a metal powder and embed it in our granular susceptor material. The third step is to place the embedded mold in our microwave furnace to melt the metal powder within the mold to form a cast part. Figure 7 shows the basic steps of the Metallum3D Microwave Digital Casting process.

wp7.png

Figure 7


As a result of the successful validation of our new microwave heating process, Metallum3D in conjunction with P3 Additive is launching a Beta Customer Program. Under this program, we are looking to identify 10 customers that have applications that could benefit from implementing our Microwave Sintering or Microwave Digital Casting process. Use the link below to apply to the Beta Customer Program.
Metallum3D Beta Customer Program
Subscribe to Our Email Newsletter


Stay up-to-date on all the latest news from the 3D printing industry and recieve information and offers from thrid party vendors.



  • Enter your email address*
  • Name
    This field is for validation purposes and should be left unchanged.





南极熊3D打印网https://www.nanjixiong.com/转自来自网络:https://3dprint.com/291470/metallum3d-successfully-completes-validation-tests-of-new-microwave-heating-process-for-additive-manufacturing/

上一篇:Sauber Technologies to install EOS P 500 3D printer as companies announce partne
下一篇:EOS President of North America Discusses the Future of Metal Laser 3D Printing
回复

使用道具 举报

推动3D打印

关注南极熊

下载手机APP

联系QQ/微信9:00-16:00

392908259

南极熊3D打印网

致力于推动3D打印产业发展

快速回复 返回列表 返回顶部